1747 UM011 EN P PDF
Publication INB-EN-P – September Installation Instructions Cette publication . User Manual, publication UM Publication IND-EN-P – November Installation Instructions. Remote I/O Scanner . UM A reference manual that contains status file . Publication INC-EN-P – August Installation . publication UM, for a listing of octal label kit catalog numbers. Slot 1. A. B. D. C.
|Published (Last):||21 November 2015|
|PDF File Size:||16.34 Mb|
|ePub File Size:||13.17 Mb|
|Price:||Free* [*Free Regsitration Required]|
Documents Flashcards Grammar checker. Per scaricarla collegarsi al sito Web indicato sopra. Gehen Sie auf die oben genannte Web-Adresse, um nach der Publikation zu suchen und sie herunterzuladen. Because of this difference, and also because of the wide variety of uses for solid state equipment, all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. No patent liability is assumed by Rockwell Automation, Inc. Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc.
UM datasheet & applicatoin notes – Datasheet Archive
Throughout this manual, when necessary, we use notes to make you aware of safety considerations. Identifies information that is critical for successful application and understanding of the product. Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss.
Attentions help you to identify a hazard, avoid a hazard, and recognize the consequences. Also, do not expose processor modules to surfaces or other areas that may typically hold an electrostatic charge. Electrostatic charges can alter or destroy memory. For general recommendations concerning installation safety requirements and safety related work practices, refer to the requirements specific to your region.
Reference the standards found in EN and your national regulations.
All cables connected to the product must remain in the enclosure or be protected by conduit or other means. La mise en garde suivante porte sur une utilisation en environnement dangereux.
routine of diagnosis
In sn, remove the protective wrap after installing the processor. Failure to remove the wrap can cause the power supply to overheat. Energize the chassis power supply. Check the chassis 1477 supply and processor LED indicators.
The power LED indicator on the power supply should be on and the fault LED indicator on the processor should be flashing. See the figure on page 9 for location of the power supply and processor LED indicators. Status of LED indicator does not matter.
Establish Communication to the Processor 1. Refer to the following table to establish communication between the processor and your personal computer. Set the communication parameters of the software to match the default parameters of the processor.
This battery provides back-up for approximately 2 years. To replace the lithium battery follow these steps. If you remove the power supply while power is applied, an electrical arc can occur.
This could cause an explosion in hazardous location installations. Remove power from the SLC power supply. Remove the processor from the chassis by pressing the retainer clips at both the top and bottom of the module and slide it out. Unplug the battery connector. Data in RAM is not lost if the battery is replaced within 30 minutes.
Remove the battery from the retaining clips. Insert a new battery into the battery retaining clips. Plug the battery connector into the socket as shown above. Re-insert the module into the SLC chassis. Restore power to the SLC power supply. Close the processor door. Refer to the chapter on troubleshooting.
It also contains explanations for all possible fault codes found in status word S: Actual scan times depend on your program size, instructions used, and the communication protocol. An explosion could result or the cells could overheat causing burns. Do not open, puncture, crush, or otherwise mutilate the batteries. Storing Store the lithium batteries in a cool, dry environment, typically Transporting One or Two Batteries – Up to two batteries can be shipped together within the United States without restriction.
Regulations governing shipment to or within other countries may differ. This exemption authorizes transport of lithium batteries by motor vehicle, rail freight, cargo vessel, and cargo-only aircraft, providing certain conditions are met.
Transport by passenger aircraft is not permitted. Explosion or violent rupture is possible. Batteries should be collected for disposal in a manner to prevent against short circuiting, compacting, or destruction of case integrity and hermetic seal.
For disposal, batteries must be packaged and shipped in accordance with transportation regulations, to a proper disposal site.
For additional information contact: The person disposing of the material is responsible for any hazard created in doing so. State and local regulations hm011 exist regarding the disposal of these materials.
For a lithium battery material safety data sheet, contact the manufacturer. Sanyo Energy Corporation Tadarand U. You can view or download publications at http: Een order paper copies of technical documentation, contact your local Rockwell Automation distributor or sales representative. For an additional level of technical phone support for installation, configuration, and troubleshooting, we offer TechConnect Support programs.
For more information, contact your local distributor or Rockwell Automation representative, or visit http: Installation Assistance If you experience a problem with a hardware module within the first 24 um01 of installation, please review the information that’s contained in this manual.
You can also contact a special Customer Support number for initial help in getting your module up and running. New Product Satisfaction Return Rockwell tests all of its products to ensure that they are fully operational when shipped from the manufacturing facility. However, if your product is not functioning, it may need to be returned. United States Contact your distributor. You must provide a Customer Support case number see phone number above to obtain one to your distributor in order to complete the return process.
Outside United States Please contact your ym011 Rockwell Automation representative for return procedure. Trademarks not belonging to Rockwell Automation are the property of their respective companies. Microsoft Word – Student Intervention Template.