ASTM D4066 PDF

April 1, 2020 By:

Buy ASTM D CLASSIFICATION SYSTEM FOR NYLON INJECTION AND EXTRUSION MATERIALS (PA) from SAI Global. ASTM D Standard Classification System for Nylon Injection and Extrusion Materials (PA). standard by ASTM International, 07/01/ View all product. 暂无评价|0人阅读|0次下载 | 举报文档. D – 01A Nylon Injection and Extrusion Materials_能源/化工_工程科技_专业资料。ASTM D标准.

Author: Shakaramar Faujora
Country: Gabon
Language: English (Spanish)
Genre: Science
Published (Last): 26 October 2007
Pages: 408
PDF File Size: 5.64 Mb
ePub File Size: 2.85 Mb
ISBN: 527-1-23150-329-4
Downloads: 32749
Price: Free* [*Free Regsitration Required]
Uploader: Nabei

I Groups 03 and 04 materials use Speci? It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

The test specimen is a disk D — 01a: Requirements are based on unannealed test specimens 3. NOTE 4—An example of this classi?

The ast, pieces are to be used for the listed relevant test methods: The designation PA indicates the following: NOTE 9—An example of this classi? This example can be applied to replace all table values, that is, tensile stress, notched Izod impact, and heat de?

Step-by-step testing shall be carried out using? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The reinforcement letter designations and associated tolerance levels are shown as follows: Q For general information not a requirement. Current edition approved August 10, The holes shall be drilled as above and then reamed, using a standard-tapered pin reamer, to a sufficient depth to allow the pins to extend approximately Packing, Packaging, and Marking This standard has been approved for use by agencies of the Department of Defense.

  ENDODONTIC PRACTICE GROSSMAN PDF

NOTE 3—An example of this classi? L Izod impact requirements for Group 04 materials based on specimens with a In general, the suffix letter gives the general requirements needed and the? Some of these compositions are also suitable for compression molding and application from solution. Link to Active This link will always route to the current Active version of the standard. This standard does not purport to address all of the safety concerns, if any, associated with its use.

Nylon 6 Supplier | Type 6/6 Nylon | Nylon Sheet

Recommended processing temperatures are shown in Table 3. Refer to Table X3. R Tensile strength and elongation shall be determined on Test Method D test specimens 3. Some of these compositions are also suitable for compression molding and application from solution. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

NOTE 7—An example of this classi? Weatherable nylon typically contains 1. Material data for inje Maximum moisture content of specimens shall be 0. The specimens tested are 3. General Principles ISO NOTE 10—When a grade of polyamide is not fully identi? Table PA is used to specify the group of nylon and Table A or B is used to specify property requirements.

  LUZHIN DEFENSE PDF

No descriptions are listed unless needed to describe a special grade under the class. Tensile strength and elongation shall be determined on Test Method D c4066 specimens 3. To be agreed upon between the user and the supplier. The specimen shall be of sufficient size so that two 4.

Industrial & Engineering Plastics

No moisture shall be intentionally added to reach this level. For the convenience of the user, Committee D20 has highlighted aatm changes that may impact the use of this classi? Start the test within 2 min after removing the specimen and wiping with a dry cloth. D — 01a Standard Classi?

O Group 07 nylons are presently used commercially only as reinforced materials. Originally published as D — Link asm Active This link will always route to the current Active version of the standard.

Viscosities for Groups 03, 04, 06, and 08 are measured as described as follows.